Were you looking for facts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately tough project. If the old bathtub is readily obtainable, the project can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub as well as place the new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually certified yourself for the task and also are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will assist you mount a brand-new bathtub in your bathroom if you have already bought a new tub as well as do not need to change the plan of your previous water pipes.
Your tools and product list need to comprise the following:
- New Bathtub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Adjustable Wrench
- Putty Knife
- Screwdriver
- Cold Chisel
- Tape Measure
- Pipe Caps
Preparing for the Installation
Firstly, the supporting structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub until the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub as well as additionally check the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the tub has actually been used at the very least once as this will certainly resolve it into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in location in between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The former kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall in between the bathroom and also the tiling, causing difficulties with wetness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof glue as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
- Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.
- Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.
- Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.
- Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.
- Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.
- If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you enjoyed our section about How to Install a Bathtub Yourself. Many thanks for taking time to read through our content. Feel free to take the opportunity to promote this blog if you enjoyed it. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule An Appointment
Comments on “How to Remove and also Change a Bathtub.”